Bay Networks 5391 Guide d'installation Page 38
- Page / 138
- Table des matières
- MARQUE LIVRES
- Remote Annex 1
- © 1996 Bay Networks, Inc 2
- Rules, Part 68 6
- Revision Level History 7
- Revision Level History 8
- Contents 9
- Contents 10
- About this Guide 15
- Printing Conventions 16
- Preface 17
- Convention: Represents: 17
- Related Documents 18
- Bay Networks Customer Service 19
- World Wide Web 21
- Customer Service FTP 22
- Support Source CD 22
- CompuServe 22
- InfoFACTS 23
- How to Get Help 24
- Remote Network Access 25
- Remote Annex 6300 Description 26
- Main Logic Board 26
- Modem Carrier Card 27
- Firmware and Software 27
- ROM Monitor 28
- Supported 28
- Configurations 28
- Watchdog Timer 28
- Front Panel 29
- Front Panel Components 30
- Network/Status 31
- (continued on next page) 31
- The button is used to: 32
- Rear Panel 33
- Rear Panel Components 34
- Physical Characteristics 35
- Before you Begin 37
- Front Mount 38
- (3 places each side) 39
- Rear Mount 40
- Bracket Mounting 41
- (2 Screws each side) 41
- Bracket Assembly 41
- (2 Screws, 2 Nuts, and 41
- 4 Washers each side) 41
- CONSOLE 10BASE5 10BASET 42
- ISDN PRI 42
- ❑ Thin Ethernet (10Base2) 43
- ❑ Thick Ethernet (10Base5) 43
- ❑ Twisted Pair (10BaseT) 43
- Ethernet cable (see 45
- Figure 2-7): 45
- Figure 2-8): 46
- Connecting a Console Terminal 47
- Annex 6300 49
- 2 Apply power 50
- 6300 to your LAN 53
- This section describes: 53
- 3 Execute the boot command 54
- BOOTP response with the sm 56
- Invoking the Console Monitor 58
- Command Descriptions 60
- Command Description Use 62
- Remote Annex 6300 is booted 72
- Remote Annex’s console port 73
- 6300 ROM Monitor commands 76
- Network test – PASSED 81
- [data bytes] [npackets] 84
- Statistic Description 87
- Bay Networks 89
- LED(s) Description 91
- Power-up and Boot Procedures 92
- N1: LEDs OK 93
- N2: Hardware OK 93
- NE2: Hardware Failure 94
- NE5: Booted wrong image 94
- Setup Mode 95
- T1: Testing LEDs 96
- T2: Testing Hardware 96
- T3: At Monitor Prompt 96
- TE2: Hardware Failure 97
- TE7: Booted Wrong Image 97
- Boot Failures 98
- Boot Error Report 99
- Error Description 100
- The broadcast address 101
- The subnet mask 101
- # /etc/erpcd –D5 103
- # boot -v 103
- Another Remote Annex 6300 104
- Remote Annex 6300 Dumps 105
- Annex overwrites crash dumps 106
- Console Port 109
- 10Base2 Ethernet Port 110
- 10Base5 Ethernet Port 111
- 10BaseT Ethernet Port 112
- PRI ISDN Interface 113
- Loopback Connectors 115
- Contents of the Kit 117
- Disassembly Instructions 118
- Installation Instructions 119
- Assembly Instructions 121
- Power-up and Test 122
- Removing Quad Modem Cards 131
- Modem Card 133
- DIP Switch S1 134
- Front of Unit 134
Produits connexes et manuels pour Logiciel Bay Networks 5391
(166 pages)
(20 pages)
(185 pages)
(162 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels