Bay Networks 5391 Guide d'installation Page 74
- Page / 138
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Remote Annex 6300 Hardware Installation Guide
Chapter 3 ROM Monitor Commands
3-16
erase
The erase command erases the contents of non-volatile memory,
including the Remote Annex 6300’s Internet address. This command
also restores the parameters to their factory defaults. The syntax is:
erase
If the self-boot option is installed, the erase command prompts for
the non-volatile memory to erase: EEPROM or FLASH. Entering 1 at
the prompt causes the Remote Annex to erase the EEPROM memory
(configuration information); entering 2 at the prompt causes the
Remote Annex to erase the Flash memory (self-boot image).
The erase command does not erase the Ethernet address.
Since the erase command erases the IP address, you must use
theaddrcommand to re-enter the Remote Annex’s IP address
before reloading any software.
The erase command display looks like this:
WARNING
monitor:: erase
1) EEPROM (i.e. Configuration information)
2) FLASH (i.e. Self boot image)
Enter 1 or 2:: 1
Erase all non-volatile EEPROM memory? (y/n) [n]:: y
Erasing 65504 bytes of non-volatile memory. Please
wait...
16K->|Data 0x0
...............................................
Initialized checksum record installed
.
.
.
- Remote Annex 1
- © 1996 Bay Networks, Inc 2
- Rules, Part 68 6
- Revision Level History 7
- Revision Level History 8
- Contents 9
- Contents 10
- About this Guide 15
- Printing Conventions 16
- Preface 17
- Convention: Represents: 17
- Related Documents 18
- Bay Networks Customer Service 19
- World Wide Web 21
- Customer Service FTP 22
- Support Source CD 22
- CompuServe 22
- InfoFACTS 23
- How to Get Help 24
- Remote Network Access 25
- Remote Annex 6300 Description 26
- Main Logic Board 26
- Modem Carrier Card 27
- Firmware and Software 27
- ROM Monitor 28
- Supported 28
- Configurations 28
- Watchdog Timer 28
- Front Panel 29
- Front Panel Components 30
- Network/Status 31
- (continued on next page) 31
- The button is used to: 32
- Rear Panel 33
- Rear Panel Components 34
- Physical Characteristics 35
- Before you Begin 37
- Front Mount 38
- (3 places each side) 39
- Rear Mount 40
- Bracket Mounting 41
- (2 Screws each side) 41
- Bracket Assembly 41
- (2 Screws, 2 Nuts, and 41
- 4 Washers each side) 41
- CONSOLE 10BASE5 10BASET 42
- ISDN PRI 42
- ❑ Thin Ethernet (10Base2) 43
- ❑ Thick Ethernet (10Base5) 43
- ❑ Twisted Pair (10BaseT) 43
- Ethernet cable (see 45
- Figure 2-7): 45
- Figure 2-8): 46
- Connecting a Console Terminal 47
- Annex 6300 49
- 2 Apply power 50
- 6300 to your LAN 53
- This section describes: 53
- 3 Execute the boot command 54
- BOOTP response with the sm 56
- Invoking the Console Monitor 58
- Command Descriptions 60
- Command Description Use 62
- Remote Annex 6300 is booted 72
- Remote Annex’s console port 73
- 6300 ROM Monitor commands 76
- Network test – PASSED 81
- [data bytes] [npackets] 84
- Statistic Description 87
- Bay Networks 89
- LED(s) Description 91
- Power-up and Boot Procedures 92
- N1: LEDs OK 93
- N2: Hardware OK 93
- NE2: Hardware Failure 94
- NE5: Booted wrong image 94
- Setup Mode 95
- T1: Testing LEDs 96
- T2: Testing Hardware 96
- T3: At Monitor Prompt 96
- TE2: Hardware Failure 97
- TE7: Booted Wrong Image 97
- Boot Failures 98
- Boot Error Report 99
- Error Description 100
- The broadcast address 101
- The subnet mask 101
- # /etc/erpcd –D5 103
- # boot -v 103
- Another Remote Annex 6300 104
- Remote Annex 6300 Dumps 105
- Annex overwrites crash dumps 106
- Console Port 109
- 10Base2 Ethernet Port 110
- 10Base5 Ethernet Port 111
- 10BaseT Ethernet Port 112
- PRI ISDN Interface 113
- Loopback Connectors 115
- Contents of the Kit 117
- Disassembly Instructions 118
- Installation Instructions 119
- Assembly Instructions 121
- Power-up and Test 122
- Removing Quad Modem Cards 131
- Modem Card 133
- DIP Switch S1 134
- Front of Unit 134
Produits connexes et manuels pour Logiciel Bay Networks 5391
Logiciel Bay Networks 5000 Manuel de service
(166 pages)
(166 pages)
Logiciel Bay Networks 5391 Manuel de service
(20 pages)
(20 pages)
Logiciel Bay Networks 5000 Spécifications
(185 pages)
(185 pages)
Logiciel Bay Networks 4000 Guide d'installation
(162 pages)
(162 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels